Electrical Engineering Stack Exchange
Electrical Engineering Stack Exchange

Questions tagged [microphone]

A sensor converting an acoustic signal into an electric one.

609 questions
28
votes
3 answers

What makes one microphone better than another, and how do I make my own?

I am curious about microphones and have a few questions. What is the key component in them which makes one better than another? What does it take to build a high quality microphone on my own? I'm looking to purchase a good microphone, and was…
capcom
  • 5,882
  • 14
  • 48
  • 59
26
votes
6 answers

Normal capacitor vs. audio capacitor

I'm building a power supply for old Schoeps CMT30F microphones. Standard condenser mic are 48V-powered nowadays, but these are 60s/70s Schoeps mic from RadioFrance/ORTF, customized at that time to be -9V or -10V powered. I need to add capacitors to…
Basj
  • 1,856
  • 4
  • 27
  • 48
18
votes
3 answers

Using a microphone with an Arduino

EDIT: I have been investigating in this problem for quite some time. It turns out to be a way more difficult project than I thought and not something for beginners. This requires expensive hardware (microphone & amplifier) and some sophisticated…
Toast
  • 363
  • 1
  • 3
  • 10
17
votes
4 answers

Electronic aspects of iPhone 3.5mm audio output

I am working for a while now on a small project of building an external mic for the iPhone to be hooked in parallel to headphones (via the 3.5 mm jack). Basically, I want to replace the iPhone's original headset microphone with another microphone,…
user11678
  • 171
  • 1
  • 1
  • 4
14
votes
3 answers

Want a USB mini-microphone array. Is it possible?

I have been learning a lot about adaptive beam-forming, and have been mucking around with various sims in MATLAB, etc. But what better way to understand something - truly understand it - than to play with the entire system? To this end, I would…
Spacey
  • 241
  • 2
  • 5
14
votes
2 answers

Digital data coming out of a cell phone headset mic?

I want to connect a sound board / mixing console / whatever-you-prefer-to-call-it to the headset jack of my Motorola Android phone. I know the typical TRRS pinout of Left/Right/Ground/Microphone, and I know about the mic being phantom-powered by…
AaronD
  • 5,596
  • 10
  • 36
12
votes
3 answers

How do I get +5v for loud noise, 0v for silence from Electret Microphone (or other components)?

I have been asking a few questions here to get to a proper one, the initial questions I asked are linked to at the end. I used Fritzing to make up some schematics of my initial thoughts, but at the very least I need help with the values on the…
Ehryk
  • 1,141
  • 5
  • 16
  • 28
12
votes
7 answers

Do electret condenser microphones require phantom power?

I was under the assumption that electret microphone capsules do not require any phantom power an can be connected in the same way dynamic microphone capsules can be, due to the fact that they contain a small permanent static charge built in. I am…
Sean
  • 1,074
  • 5
  • 13
  • 19
12
votes
3 answers

How to make a clean amplified microphone analog to digital conversion?

I've asked a couple of questions relating to this project the past couple of days, but I cant seem to put it all together. I hooked up an electret mic into an opamp and gave output to my arduino microcontroller. The ADC on the microcontroller…
Shubham
  • 6,054
  • 12
  • 41
  • 55
10
votes
6 answers

Generating a differential signal

I was given a small task (actually it's part of a much larger task) where the requirement is to generate a signal which looks like it came from a microphone. The following requirements needs to be kept: 1.0Vpp Sine Wave Differential Now these are…
Tom L.
  • 7,969
  • 1
  • 19
  • 34
10
votes
3 answers

Using a microphone from the 1930s

I have an old Braun Cosmophon BMF2020 microphone at home, which I have long been wanting to use for good ol' fun. I have virtually no technical knowledge, so I am completely uncertain how to power the device, and if it would be possible to connect…
Tim Stack
  • 213
  • 2
  • 8
10
votes
7 answers

Can a comparator (LM393) be used as an amplifier?

I have seen modules for microphones (such as the one below) that use the LM393 and claim to have amplification. I have looked this part up and it is a comparator. I have read that op amps can be used as comparators, but I don't understand if the…
Arik Yavilevich
  • 301
  • 1
  • 2
  • 12
9
votes
4 answers

Can I use a PNP Transistor with an Electret Microphone to get an non-inverting output for my Arduino?

I'm looking to simply read the generic sound level from an Electret Microphone. I've seen a number of schematics with NPN transistors, that will provide an inverted output (~5V when quiet, ~0V when loud, linear operation in between). Here's an…
Ehryk
  • 1,141
  • 5
  • 16
  • 28
9
votes
3 answers

Electret Microphone preamplification - will it work for dynamic type microphone?

I'd like to use this diagram to pre-amplify a microphone signal in order to activate the analog input of my arduino (source: reconnsworld.com) Will it work with a dynamic microphone in place of an electret microphone?
Joseph
  • 203
  • 2
  • 6
9
votes
3 answers

How to connect microphone to an Arduino with an opamp?

I'm trying to connect a contact microphone to an Arduino. I got a couple of LM833N audio dual opamps, which I'd like to put to use. I'm still struggling to understand opamps, though. I've been reading an instructable on audio input on the Arduino.…
loopbackbee
  • 191
  • 1
  • 3
1
2 3
…
40 41